Stapler/Folder Model 60/61 Service manual OCTOBER 1994
REP 2.5 Parallelity Staple stop - Anvils T08009 TJ PURPOSE The purpose is to obtain the correct staple position. 1. Switch off the main po
REP 2.6 Parallelity Fold stop - Fold knife T08009 TJ PURPOSE The purpose is to obtain the correct folding position. 1. Switch off the mai
REP 2.7 Positioning staples on fold T08009 TJ PURPOSE The distance between the fold stop and the fold knife should be equal to the d
REP 2.8 Adjustment stapler position to Anvil T08009 TJ PURPOSE By checking the staples on a stapled set you can easely determine if the st
REP 2.9 Adjustment stapler pressure T08009 TJ PURPOSE It is possible to staple through 22 sheets of paper without adjusting the stapler
REP 2.10 Home position Stapler motor M1 T08009 TJ PURPOSE Switch SW7 stops the Stapler motor at home position. There are two springs tha
REP 2.11 Home position Knife motor M2 T08009 TJ PURPOSE Switch SW8 stops the Knife motor at home position. 1. Remove Front and Infeed co
REP 2.12 Adjustment of Eject Idler roller T08009 TJ PURPOSE The upper Idler roller has to be positioned at the correct height in order f
REP 2.13 Adjustment of Eject motor M4 T08009 TJ PURPOSE There should be a clearance between the Idler roller and the Eject feed wheel whe
REP 2.14 Aligning Eject rollers T08009 TJ PURPOSE This adjustment is more essential on the Model 61, when the set is fed to the Fold s
i Contents T08011 TJ PAGE INTRODUCTION ii OCTOBER -94 COVER REMOVE INSTRUCTION (CRI) CRI 1.1 Front
REP 2.15 Removal of lower Fold rollers T08009 TJ REMOVE 1. Switch off the main power switch and disconnect the power cord. 2. Remove Fro
REP 2.16 Fold pressure, top Fold rollers T08009 TJ PURPOSE There are two springs on each side of the top Fold rollers, one is stiff and
REP 2.17 Removal of Infeed Motor M6 assembly, Model 61 T08009 TJ PURPOSE By removing the infeed motor assembly you will have an easy access to t
REP 2.18 Removal of Stapler head T08009 TJ REMOVAL 1. Switch off the main power switch and disconnect the power cord. 2. Remove the Stap
EDI 3.1 Trimming of Circuit board PCB 60-1 T08009 TJ PURPOSE The trimmers on the circuit board can be adjusted in order to increase or decrease
FIP 4.1 Fault isolating procedure Model 61 T08012 TJ Observed fault Possible cause Fault isolating/repair No machine initialisation. P
ii Introduction T08011 TJ GENERAL INFORMATION This service manual describes both the Model 60 and the Model 61. Also available is con
FIP 4.1 Fault isolating procedure Model 61 T08012 TJ Observed fault Possible cause Fault isolating/repair Stapler motor M1 Fuse F2 de
FIP 4.1 Fault isolating procedure Model 61 T08012 TJ Observed fault Possible cause Fault isolating/repair Fold knife motor M2 Home pos
FIP 4.1 Fault isolating procedure Model 61 T08012 TJ Observed fault Possible cause Fault isolating/repair False jam indication Main c
FIP 4.2 Fault isolating procedure Model 60 T08012 TJ Observed fault Possible cause Fault isolating/repair No machine initialisation. P
FIP 4.2 Fault isolating procedure Model 60 T08012 TJ Observed fault Possible cause Fault isolating/repair Stapler motor M1 Home posit
FIP 4.2 Fault isolating procedure Model 60 T08012 TJ Observed fault Possible cause Fault isolating/repair Belt stacker motor M5 Main
MAI 5.1 Preventive MaintenancePreventive Maintenance Bookletmaker Model 60 / 61Service interval: 80 000Note: All INSTRUCTIONS are referring to the S
TNIOPKCEHCNOITCURTSNIECNEREFER00008000061000042ELUDOMDEEFNI16LEDOMleehwdeefnIlohoclarotavitcaerrebburaesU.ecalpernrowfI.raewrofkcehC.diulf9.2egaP8metI
CRI 1.1 Front and rear cover T08010 TJ FRONT COVER REMOVAL 1. Loosen the two screws (1). 2. Pull out the lower end and lift up to rem
CRI 1.2 Infeed and outfeed cover T08010 TJ UPPER/LOWER INFEED COVER REMOVAL 1. Remove the two screws (1). 2. Pull out the upper end
REP 2.1 Parallelity Fold knife - Anvil bar T08008 TJ PURPOSE The purpose is to align the Anvil bar with the Fold knife to obtain a correct
REP 2.2 Adjustment of Side guides Model 60 T08008 TJ PURPOSE Side guides needs to have the correct position in order to transport the set
REP 2.3 Adjustment of Side guides Model 61 T08009 TJ PURPOSE The Side guides needs to be exactly parallel in order to transport the set s
REP 2.4 Adjustment of side jogger movement Model 61 T08009 TJ PURPOSE On the Model 61 the side jogging is performed with the rear jogging rail
Commentaires sur ces manuels